ATTSUMI ELECTRIC CO., LTD. INTELLIGENT OUTDOOR DETECTOR SIR05RA Installation Manual

1. SAFETY PRECAUTIONS

Please read these safety precautions carefully before installation and operation to ensure proper use.

Symbols

• DANGER: Indicates immediate hazardous situations which, if not avoided, will result in death or serious injury.
• WARNING: Indicates hazardous situations which, if not avoided, could result in death or serious injury.
• CAUTION: Indicates hazardous situations which, if not avoided, could result in minor or moderate injury.
• NOTE: Provides information crucial for proper installation or operation.

General Precautions

• Installation should be performed by a specialist.
• Ensure proper wiring according to instructions.
• Avoid installation in places exposed to water or high humidity.
• Do not drop or apply strong impact to the product.
• Do not touch the lens directly.
• Keep the product clean.
• Disconnect power before servicing.
• Do not disassemble or modify the product.

2. INTRODUCTION

Features

• Dual detection method (PIR & Microwave).
• Detection range up to 12m.
• Anti-masking function (IR reflection).
• Self-check function.
• Fine sensitivity adjustment.
• Advanced temperature compensation.
• Horizontal & vertical detection area adjustment.
• Walk test mode.

Precautions for Installation

• Avoid heat sources (air conditioners, heaters).
• Avoid moving objects (clotheslines, trees).
• Avoid strong winds.
• Install on a solid, stable surface.
• Avoid direct sunlight, car lights, or light sources.
• Avoid uneven ground or obstructions.
• Avoid metallic walls or surfaces.

Main Applications

• Monitoring entrances, approaches, backyards, garages, windows, etc.

Part Names and Indications

Sensor Unit

• PIR Sensor (1)
• Microwave Module (2)
• Anti-masking Sensor (3)
• Walk Test LED (4)
• Power LED (5)
• Anti-masking LED (6)
• Sensitivity Adjuster (7)
• DIP Switch (8)
• Terminal Block (9)
• Housing Removal Button (10)
• Mounting Screw Hole (11)
• Wiring Inlet (12)
• Leveler (13)

Housing & Back Box

• Housing (A)
• Screw (B)
• Mounting Hole (C)
• Knockout Hole (D)
• Cable Inlet (E)

3. HOW TO REMOVE/ATTACH THE HOUSING

Follow the illustrated steps to safely remove and attach the housing for installation and maintenance.

4. WIRING

Terminal Block

• (+) (-): Power input (DC10.5-28V)
• ALM (NO/NC): Alarm output (N.C. 28VDC 0.1A max. N.O. 28VDC 0.1A max)
• TAMPER (N.C.): Tamper output (N.C. 28VDC 0.1A max)
• AM (N.C.): Anti-masking output (N.C. 28VDC 0.1A max)

Connection Examples

Illustrations show wiring for N.C. output alarm, N.O. output alarm, and anti-masking output.

5. INSTALLATION POSITION

Install the sensor at a height of 0.8-1.2m (2.6-3.9ft). Adjust the horizontal and vertical angles for optimal detection. Refer to the diagrams for detection area patterns.

6. SETTING OF DETECTION AREA

Horizontal Area Adjustment

The sensor unit can be rotated horizontally up to 90 degrees left and right.

Vertical Area Adjustment

Adjust the vertical angle (0°, 2.5°, 5°, 7.5°, 10° down) by repositioning the sensor unit.

Detection Range Adjustment

Adjust the detection range using the sensitivity adjuster (variable resistor).

Area Masking

Use the provided masking seals to restrict the detection area and prevent false alarms. Diagrams illustrate how to apply masks for various scenarios (e.g., avoiding obstacles, narrow areas).

7. DIP SWITCH SETTINGS

Configure the sensor's operation using the DIP switches (1-8).

• DIP SW1-2: Mode Selection (e.g., PIR Only, MW Only, PIR & MW AND/OR, PIR & MW AND)
• DIP SW3: Detection Pattern (AND/OR Logic)
• DIP SW4: Sensitivity (LOW/HIGH)
• DIP SW5: Anti-masking output (ON/OFF)
• DIP SW6: Microwave detection range (SHORT/LONG)
• DIP SW7-8: Alarm output timer (2/5 sec)

8. WALK TEST

Perform a walk test after installation to ensure proper detection. The walk test LED will illuminate upon detection.

9. CHECKING BEFORE/AFTER INSTALLATION

Inspection Points

• Power connection
• Wiring connections
• Tamper switch operation
• Detection performance
• Anti-masking function

10. TROUBLESHOOTING

A table provides common symptoms, possible causes, and corrective measures for issues like no detection, constant alarms, or anti-masking alarms.

11. OUTLINE DIMENSIONS

Detailed diagrams with measurements (in mm and inches) of the sensor unit and housing.

12. SPECIFICATIONS

13. OPTIONAL COMPONENTS

List of optional accessories for the detector, including various mounting brackets.

ATTSUMI ELECTRIC CO., LTD.