Manuale installatoreABS_GSM

TABLE OF CONTENTS

INTRODUCTION

Hereby, BENTEL SECURITY declares that the ABS-GSM Module is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The complete R&TTE Declaration of Conformity for each Device can be found at www.bentelsecurity.com/dc.html.

Installation of these systems must be carried out in compliance with the local laws and bylaws in force. This Communicator is fixed and shall be installed by Service Persons only (service person is defined as a person having the appropriate technical training and experience necessary to be aware of hazards to which that person may be exposed in performing a task and of measures to minimize the risks to that person or other persons). It shall be installed and used within an environment that provides the pollution degree max 2, over voltages category II, in non-hazardous, indoor locations only. This manual shall be used with the Installation Manual of the alarm control panel. All instructions specified within that manual must be observed.

These devices have been designed and made to the highest standards of quality and performance. The manufacturer recommends that the installed system should be completely tested at least once a month. BENTEL SECURITY srl shall not be responsible for damage arising from improper installation or maintenance by unauthorized personnel. BENTEL SECURITY srl reserves the right to change the technical specifications of this product without prior notice.

These instructions describe how to install the ABS-GSM GSM module. For device settings and information on how to use the module's functions, as well as any other information, please consult the ABSOLUTA Installer Manual and User Manual. The ABSOLUTA Manuals may be obtained from your distributor and downloaded from the www.bentelsecurity.com website.

FreeRTOS Notes

This product uses the FreeRTOS.org real time kernel. The FreeRTOS.org source code can be obtained by visiting http://www.FreeRTOS.org.

FreeRTOS LICENSING:

"The FreeRTOS source code is licensed by the GNU General Public License (GPL) with an exception. The full text of the GPL is available here: http://www.freertos.org/license.txt. The text of the exception is available on FreeRTOS official website: http://www.FreeRTOS.org/License_and_Warranty_Page. The exceptions permits the source code of applications that use FreeRTOS soley through the API published on this WEB site to remain closed source, thus permitting the use of FreeRTOS in commercial applications without necessitating that the whole application be open sourced. The exception should only be used if you wish to combine FreeRTOS with a proprietary product and you comply with the terms stated in the exception itself."

INTRODUCTION

Features

• Quad Band
• Support for GSM/GPRS
• Primary or Backup Phone Alarm Communicator
• Voice Message Transmission via GSM
• Contact ID transmission via GSM
• Event Notification via SMS
• Library of 250 SMS: 1 header, 8 status and 241 custom
• 32 events controlled via SMS
• 32 events controlled via caller ID (free of charge)
• Control panel status verified via SMS
• Verify remaining balance on pre-paid SIM card
• Teleservice via the Internet (GPRS)

Description

ABS-GSM is a GSM module that can be used by the ABSOLUTA control panel as a backup alarm communicator in the event of a failure or sabotage of the integrated PSTN alarm communicator, or completely replace it in areas covered by the GSM network but where PSTN is not available. In that sense, the GSM module is completely transparent to the control panel for: transmitting Voice Messages via GSM; transmitting events with Contact ID via GSM;

Functions

The GSM module can also be used to: send text messages to a series of phone numbers to report events (alarms, sabotage, failures, etc.); activate/deactivate the control panel actions (outputs, voice messages, etc.) by sending an SMS to the GSM module phone number; trigger actions simply by recognising the number calling the GSM module (free of charge); check the status of the control panel via telephone, by sending and receiving SMS; perform Teleservice (management and remote programming of the control panel) via the Internet, on the GPRS channel.

The ABSOLUTA control panel communication system with the GSM module.

PARTS IDENTIFICATION

Parts Identification: a) GSM Module, ABS-GSM; b) antenna for metal box, BGSM-100CA; c) antenna for plastic box, ABS-AK.

• Reserved terminal board
• PC-LINK connector
• Operating lights
• Radio Module
• Connector for the antenna
• Antenna for Plastic Box
• Nut
• Washer
• Connector for the antenna 6
• ABS-AK antenna cable
• Connector for connecting to GSM module
• SIM card (NOT included)
• Angle brackets for fixing the motherboard
• SIM holder
• Connector for connection to the motherboard
• Microprocessor

INSTALLATION

General Precautions

Before installing the GSM module, make sure the control panel is NOT connected to the power supply. Before inserting or removing the SIM card, make sure that the GSM module is NOT connected to the power supply. Disable the PIN and call transfer on the SIM card before inserting it into the GSM module.

Module Installation

The ABS-GSM GSM module can be installed in the metal ABS-M box and in the ABS-P plastic one, as shown respectively in Figures 3a and 3b (part no. 23) and described below.

Steps:

1. Insert the SIM card (NOT included) into the SIM-holder 14 of the Module.
2. Insert the GSM module to the connector 21 (GSM/GPRS), making sure that the holes in the angular brackets 13 on the Module coincide with the holes 19 on the motherboard.

WARNING: The GSM Module may be severely damaged if not properly inserted.

3. Secure the GSM module to the holes 19, using the screws provided.

Antenna Installation

Metal Box

To install in the metal ABS-M box you need antenna BGSM-100CA (Figure 2b).

Steps for Metal Box Antenna:

4. Position antenna BGSM-100CA on the upper side of the metal box, as far as possible from the wall.
5. Pass the antenna cable through hole 18 in the bottom of the control panel, then connect it to connector 5 on the GSM module.
6. Secure the antenna cable to the fastener 17.

Plastic Box

To install in the plastic ABS-P container, you need antenna ABS-AK (Figure 2c).

Steps for Plastic Box Antenna:

7. Remove nut 7 and washer 8 from connector 9 of the cable 10 supplied with antenna ABS-AK.
8. Insert connector 9 into hole 25 of the ABS-P container.
9. Insert washer 8 and tighten nut 7 until connector 9 is fastened.
10. Screw antenna 6 onto connector 9.
11. Screw connector 11 onto connector 5 of the Module.

GSM Signal Strength Check and Programming

Check that the GSM signal strength is sufficient in the place where the control panel is to be installed (see the BOSS Status page or the GREEN light on the Module); if is NOT strong enough, try moving the antenna onto the metal container or the control panel, or else try the outdoor antenna ANT-EU. Program the options for the GSM module as described in the ABSOLUTA Installation Manual.

Operating lights

The GSM module has two operating lights (part no. 2 in Figure 2 on page 8) that light up to show troubles and the GSM signal strength, as described below. When the module is turned on, both lights turn on for an instant, indicating that the module is on.

RED (T) light

The RED (T) light is normally off; it flashes at a frequency of 1 s (0.5 s on/0.5 s off) to indicate that there is a trouble, as described below: between each sequence there is a pause lasting 2 s.

Trouble Priority

If there is more than one trouble at any one time, the light indicates the one with higher priority. The first column on this page indicates the priority of the trouble (1 corresponds to the highest priority) and the number of flashes (priority/flashes).

• 1/1 Invalid Firmware: The GSM module requires a valid firmware.
• 2/2 Power Trouble: The supply voltage powering the module is below the minimum required value.
• 3/3 Radio Module Trouble: The microprocessor cannot communicate with the Radio Module.
• 4/4 SIM Trouble: The microprocessor cannot communicate with the SIM card or is unable to unlock the SIM card PIN.
• 5/5 GSM Network Trouble: The Radio Module cannot connect to the GSM network.
• 6/6 GPRS Trouble: The GSM module cannot connect to the GPRS network (e.g. the APN settings may be invalid).
• 7/7 Receiver not available: The GSM module is unable to complete the initialization procedure with an IP receiver over the GPRS network.
• 8/8 Receiver 1 absent: Supervision with receiver 1 fails.

GREEN (S) light

The GREEN (S) light indicates the strength of the GSM signal, as described below.

• Off: No signal.
• Flashing slowly: Low signal.
• Flashing rapidly: Good signal.
• On: Excellent signal.

Technical Specifications

• Voltage: 10 ÷ 27.6 VDC
• Current Draw: 250 mA @ 12 VDC
• Operating Temperature: -10 ÷ +40 °C
• Operating Humidity (not condensed): 0 ÷ 93% RH
• Dimensions (WxHxD): 99x65.5x12 mm
• Weight: 42 g

Recycling information

BENTEL SECURITY recommends that customers dispose of their used equipments (panels, detectors, sirens and other devices) in an environmentally sound manner. Potential methods include reuse of parts or whole products and recycling of products, components, and/or materials.

Waste Electrical and Electronic Equipment (WEEE) Directive

In the European Union, this label indicates that this product should NOT be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling. For specific information see: http://www.bentelsecurity.com